Abstract

Um método eletroquímico de baixo custo foi desenvolvido para a determinação de traços de metil paration (MP) baseado nas propriedades do eletrodo de grafite pirolítico de plano basal modificado com grafite (grafite-bppg). A combinação do grafite-bppg com voltametria de onda quadrada (VOQ) resultou em um método eletroquímico seletivo, sensível e original para a determinação do pesticida MP em água potável. O eletrodo foi construído e o comportamento eletroquímico do MP foi estudado. A imobilização foi feita através de modificação por formação de filme a partir da dispersão de pó de grafite em água destilada e através de pipetagem de um volume pequeno sobre a superfície do eletrodo, permitindo que o solvente volatilizasse. A forte afinidade do modificador grafite com o grupo fósforo do MP permitiu o depósito de uma quantidade significativa de MP em menos de 60 segundos. Os resultados de voltametria cíclica mostraram que o eletrodo de grafite-bppg pode aumentar a sensibilidade na intensidade de corrente para os picos redox quasi-reversíveis dos produtos da redução catódica do grupo nitro em potencial negativo (pico I = 0,077 V e o pico II = -0,062 V) e para o pico catódico irreversível (pico III = -0,586 V) em comparação com o eletrodo não modificado bppg e que o processo é também controlado por adsorção. Sob condições otimizadas, o intervalo de concentração e limite de detecção para o pesticida MP são 79,0 a 263,3 mmol L -1 e 3,00 mmol L -1 , respectivamente. O método proposto foi aplicado com sucesso à determinação do MP em água potável e o desempenho deste sensor eletroquímico foi avaliado em termos de figuras de mérito analíticas. A low-cost electrochemical method was developed for the determination of trace-level of methyl parathion (MP) based on the properties of graphite-modified basal plane pyrolytic graphite electrode (graphite-bppg). A combination of graphite-bppg with square-wave voltammetric (SWV) analysis resulted in an original, sensitive and selective electrochemical method for determination of MP pesticide in drinking water. The electrode was constructed and the electrochemical behavior of MP was studied. Immobilization is achieved via film modification from dispersing graphite powder in deionized water and through pipeting a small volume onto the electrode surface allowing the solvent to volatilize. The strong affinity of the graphite modifier for the phosphorous group of the MP allowed the deposition of a significant amount of MP in less than 60 seconds. The cyclic voltammetric results indicate that the graphite-bppg electrode can enhance sensitivity in current intensity towards the quasi-reversible redox peaks of the products of the cathodic reduction of the nitro group at negative potential (peak I = 0.077 V and peak II = -0.062 V) and that the cathodic irreversible peak (peak III = -0.586 V) in comparison with bare bppg electrode and is also adsorption controlled process. Under optimized conditions, the concentration range and detection limit for MP pesticide are respectively 79.0 to 263.3 mmol L -1 and 3.00 mmol L -1 . The proposed method was successfully applied to MP determination in drinking water and the performance of this electrochemical sensor has been evaluated in terms of analytical figures of merit. Keywords: methyl parathion, basal plane pyrolytic graphite electrode, square-wave voltammetry, graphite, drinking water Okumura et al. 653 Vol. 22, No. 4, 2011 Introduction Organophosphorous (OP) compounds are the most important agrochemical used in the Brazilian agriculture and are significant environmental and food chain pollutants 1 because they are used intensively as pesticides, insecticides and chemical-warfare agents. Their uninformed use can cause food, water, soil, etc contamination and, due to its high toxicity, rapid detection of these toxic compounds has become increasingly important for homeland security and health protection. 2 Analysis of OPs in the environment is routinely carried out using gas or liquid chromatography associated with mass spectrometry or others detectors. Among OP compounds, MP exhibits good redox activities at some electrode surfaces. 17 Compton et al. 18, 22-28 Despite of all of the advantages presented above on the use of glassy carbon electrode (or others electrode surfaces) modified by CNTs and/or several (nano)particles, the graphite-bppg electrode has not been evaluated in terms of electroanalytical use and electrocatalystic effects, and to assess whether it is characterized by the same features mentioned. Furthermore, we evaluated if the graphite used in the modification of the electrode has the same advantages to the nanomaterials and nanoparticles used in papers cited previously, and if the electron transfer process is facilitated. The assessment of this study will propose the replacement of such nanoparticles and nanomaterials in the construction of new electrodes taking into account the cost of production using only the graphite in the modification process. Additionally, to the best of our knowledge, anodic stripping voltammetric determination of MP using a graphite-bppg electrode has not been reported in the literature. The aim of the present work is to develop a convenient and sensitive method for the determination of MP based on the unusual, and not fully explored, properties of graphite as a modifier. Experimental Reagents All chemicals were of analytical grade and were used without any further purification. MP was supplied by SigmaAldrich (> 99%, St. Louis, USA) and a stock solution of 38 mmol L -1 was prepared in methanol (Fisher, HPLC grade, USA) and used in all experiments. Graphite powder was obtained commercially from Merck (product number 1042062500, black powder, ≥ 99.5%, particle size < 50 µm, Germany). Acetate buffer solution was purchased by Acros Organics (> 99%, Belgium) and pH was adjusted with NaOH 0.1 mol L -1 solution (Vetec, Brazil). All solutions were prepared with deionized water of resistivity not higher than 18.2 MW cm -1 (Millipore, Milli-Q System, USA). Instrumentation Voltammetric measurements were carried out using a m-Autolab type III (Eco-Chemie, The Netherlands) potentiostat. All measurements were conducted using a three-electrode configuration. A homemade basal plane pyrolytic graphite electrode in polytetrafluorethilene polymer (5 mm diameter, Le Carbone Ltd, Sussex, U.K.) was used as the working electrode. The counter electrode was a bright platinum bare (diameter 5 mm and length 50 mm, Eco-Chemie, Netherlands). Finally, the reference electrode used was Ag|AgCl, KCl 3.0 mol L -1 (Eco-Chemie, Netherlands). The pH of the solutions was measured using a pHmeter from Metrohm, model 826. Preparation and modification of the electrode The graphite-bppg electrode was prepared using exactly the same procedure described by Compton et al. 29 with the slight difference that the film of graphite powder was formed via dispersion of 18.0 g of graphite power in 15.0 mL of deionized water under sonicated conditions for 15 min. Other types of dispersion were evaluated using the acetonitrile, methanol and DMF, however the results were unsatisfactory due to the lack of reproducibility of the electrochemistry measurements. Additionally, no effects of blocking or fouling surface was obtained using the graphitebppg electrode, even when leach out of the graphite film in aqueous solutions during the electrochemical experiments. Before each experiment the bppg electrode was first polished on a polishing cloth with an aqueous suspension of 0.05 and 0.30 µm alumina slurry solution and ultrasonically cleaned for 5 min in a 1/1 ethanol:H 2 O mixture, then rinsed with distilled water and dried at room temperature. The electroactive areas of both bare bppg and graphitebppg electrodes were obtained by cyclic voltammetry (CV) using K 3 [Fe(CN) 6 ] as a probe at different scan rates in 25 °C. For a reversible process at 25 °C , the RandlesSevcik formula has been used: where i pa refers to the anodic peak current, n is the number of electrons transferred, A is the surface area of the electrode, D R is diffusion coefficient, n is the scan rate and , then from the slope of the plot of i pa versus n ½ relation, the electroactive areas were calculated. In bare bppg, the electrode surface was found to be 0.196 cm 2 and for graphite-modified bppg, and the surface was nearly 4-4.5 times greater. Electrochemical stripping detection of MP The determination of MP included one main step, as is usual for an analytical procedure. The graphite-bppg electrode was immersed into a stirred 10.0 mL sample solution containing desired concentration of MP by an accumulation potential during a given time, and then anodic stripping SWV measurements were undertaken. Several electrochemical methods of analysis were applied, such as linear sweep (LSV), differential-pulse (DPV) and square wave voltammetry (SWV). All measurements were carried out at 25.0 ± 0.1 °C and were also obtained in triplicate. An analytical curve of MP in 0.20 mol L -1 acetate buffer (pH 5.2) was obtained by standard addition of MP with concentrations ranging from 79.0 to 263.3 mmol L -1 using the anodic stripping SWV technique. To study the accuracy of the proposed method and to check the interferences, recovery experiments were carried out in the drinking water samples (9.00 mL of the sample + 1.00 mL of the 2.0 mol L -1 acetate buffer solution and pH adjusted to 5.2). Results and Discussion Cyclic voltammetry behavior of MP All voltammetric measurements were carried out using an already optimized 0.20 mol L -1 acetate buffer (pH 5.2) system, which promotes complete solubilization of the MP and is also characterized by an improvement of the potential window. A well-known mechanism to understand MP redox reactions has been already proposed Additionally, in order to understand the electrochemical behavior of MP still using CV, after the second sweep, the peak current decreased greatly and finally remained unchanged (1 st outer and 10 th inner cycle, Useful information about electrochemical mechanisms can usually be acquired from the relationship between peak current and scan rate by CV measurements. Therefore, the electrochemical behavior of MP at different scan rates from 0.010 to 0.300 V s -1 was also studied in the graphite-modified bppg electrode. There is a good linear relationship between peak current and scan rate as indicated by Influence of amount of graphite dispersed in deionized water In order to develop a voltammetric method for determining the MP, the SWV mode was selected, because the peak is sharper and better defined at lower concentrations of MP than those obtained by linear sweep and differential-pulse voltammetric techniques. As a consequence a lower background current was used resulting in improved resolution for the MP reversible peak obtained previously by CV measurements. Influence of accumulation potential and time It is important to fix the accumulation potential (E deposit ) and time when adsorption studies were undertaken for analytical purposes, using electrochemical anodic stripping. Both conditions could affect the amount of adsorption of MP at the graphite-modified bppg electrode because the nitro group of MP is reduced at maximum rate giving the corresponding hydroxylamine product which in turn is responsible of peaks I and II at about 0 V. Bearing this in mind, the effect of accumulation potential and time on peak current response was studied by SWV as shown in the Optimization of SWV conditions After the evaluation of the optimal conditions for the modification of the bppg-electrode with graphite, the optimal parameters for the SWV technique that yielded the best results for MP stripping analysis were assessed. Initially, three parameters were tested: amplitude, step potential and frequency (all of the measurements were carried out using univariate tests). The amplitude varied in the range of 10-100 mV, fixing the frequency at 50 Hz and step potential at 4.5 mV. The best result was defined with the parameters that cause no deformation of the peak potential or any significant increase in peak width. As a consequence, 100 mV was chosen as the square-wave amplitude. Secondly, the frequency was evaluated in the range of 10-100 Hz, maintaining amplitude of 100 mV and a step potential of 4.5 mV. It should be noted that, according to GPES 4.9 software version, the potential step (or potential increment) together with the frequency defines the effective scan rate of SWV mode. The best voltammograms were obtained using 50 Hz for the analysis of MP. The response of peak currents increases up to 80 Hz and after that point remains stable (with a slight reduction of peak current and no deformation in the voltammetric shape of MP oxidation process). Finally, by fixing the amplitude at 100 mV and the frequency at 50 Hz, the effect of potential step increment was studied in the range of 1-10 mV. For potential steps greater than 1 mV, the current peak was observed to decrease in height for MP. Therefore, for the optimized conditions, the analysis of MP in graphitemodified bppg electrode was carried out using amplitude of 100 mV, frequency of 50 Hz and step potential of 1 mV (corresponding to an effective scan rate of 50.0 mV s -1 ). Calibration curve According to the observed SWV results, it was possible to apply this technique to the quantitative analysis of MP. The 0.2 mol L -1 acetate buffer solution (pH 5.2) was selected as the supporting electrolyte for the quantification of MP giving the maximum peak current. The peak at about + 0.074 V was considered most appropriate for the analysis. Anodic stripping square-wave voltammograms obtained with increasing amounts of MP demonstrate that the peak current increased linearly with increasing concentration where s is the standard deviation of the peak currents of the blank (twelve runs), and m is the slope of the calibration Braz. Chem. Soc. 658 curve. The LOD obtained is satisfactory and less sensitive than those reported in literature, however these results clearly indicate that the proposed electrochemical method of analysis for the determination of MP pesticide is reliable, rapid and especially low-cost. Additionally, to study the reproducibility of the electrode preparation procedure, a 263.3 mmol L -1 MP solution was measured with the same electrode (with a renewed electrode surface with graphite as a modifier for each measurement) for several hours per day, the R.S.D. of the peak current was 10.8% (number of measurements = 12). Between days reproducibility was similar to that of within day results without considerable variation. Analysis of drinking water In order to evaluate the applicability of the proposed method in the drinking water sample analysis, five samples were studied. Initially, voltammograms in sample solutions containing the supporting electrolyte and various aliquots of the drinking water were recorded and no oxidation peaks were observed in any of the five samples, demonstrating the absence of detectable residues of MP pesticide in these matrices. The procedures for the MP analysis followed a standard addition method carried out after the addition of known amounts of the MP to various samples (3 consecutive additions of 55.0 mmol L -1 ) with proposed contaminated samples with 55.0 mmol L -1 . The results were consistent and demonstrated a clear linear relationship. The electrochemical response was satisfactory, and a recovery test of MP ranged from 55.0 to 220.0 mmol L -1 was also performed using anodic stripping SWV. The recoveries in different samples were in the range from 98.5 to 103%, with each respectively R.S.D. estimated Under the optimum experimental conditions, the effects of potential interferents on the voltammetric response of 55.0 mmol L -1 MP were also evaluated. The experimental results However, a concentration of sorbic acid had a significant influence on the voltammetric signal of MP. Conclusions In this work, a graphite-modified bppg electrode has been successfully developed for oxidation of MP in a 0.20 mol L -1 acetate buffer solution (pH 5.2). Graphite powder showed greater sensitivity action for the oxidation of MP, characterized by the enhancement of the peak current, which was probably due to the larger surface area of graphite attached to the electrode. The peak at about + 0.074 V was suitable for analysis and the peak current had a linear relationship with MP concentrations over a certain range under the selected conditions. This sensor can be used for voltammetric determination of the analyte as low as 10.0 µmol L -1 with good reproducibility. The modified electrode was also been used to determine MP in drinking water samples. The proposed method offers the advantages of accuracy and time saving as well as simplicity of reagents, costs and apparatus. In addition, the results obtained in the analysis of MP in spiked drinking water samples demonstrate the high potential applicability of the method for real sample analysis.