This paper presents a comprehensive survey of existing techniques for interconnect optimization during the VLSI physical design process, with emphasis on recent studies on interconnect design and optimization for high-performance VLSI circuit design under the deep submicron fabrication technologies. First, we present a number of interconnect delay models and driver/gate delay models of various degrees of accuracy and efficiency which are most useful to guide the circuit design and interconnect optimization process. Then, we classify the existing work on optimization of VLSI interconnect into the following three categories and discuss the results in each category in detail: (i) topology optimization for highperformance interconnects, including the algorithms for total wire length minimization, critical path length minimization, and delay minimization; (ii) device and interconnect sizing, including techniques for efficient driver, gate, and transistor sizing, optimal wire sizing, and simultaneous topology construction, buffer insertion, buffer and wire sizing; (iii) highperfbrmance clock routing, including abstract clock net topology generation and embedding, planar clock routing, buffer and wire sizing for clock nets, non-tree clock routing, and clock schedule optimization. For each method, we discuss its effectiveness, its advantages and limitations, as well as its computational efficiency. We group the related techniques according to either their optimization techniques or optimization objectives so that the reader can easily compare the quality and efficiency of different solutions.

Buffer insertion seeks to place buffers on the wires of a signal net to minimize delay. Van Ginneken [14] proposed an optimal dynamic programming solution (with extensions proposed by [7] [8] [9] [12]) such that at most one buffer can be placed on a single wire. This constraint can hurt solution quality, but it may be circumvented by dividing each wire into multiple smaller segments. This work studies the problem of finding the correct number of segments for each wire in the routing tree. Too few segments yields sub-par solutions, but too many segments can lead to excessive run times and memory loads. We derive new theoretical results for computing the appropriate number of buffers (and hence wire segments) which motivate our new wire segmenting algorithm. We show that using wire segmenting as a precursor to buffer insertion produces solutions within a few percent of optimal, while using only seconds of CPU time. 1 Introduction The scaling of process technology and device and interco...

Interconnect has become the dominating factor in determining circuit performance and reliability in deep submicron designs. In this embedded tutorial, we first discuss the trends and challenges of interconnect design as the technology feature size rapidly decreases towards below 0.1 micron. Then, we present commonly used interconnect models and a set of interconnect design and optimization techniques for improving interconnect performance and reliability. Finally, we present comparisons of different optimization techniques in terms of their efficiency and optimization results, and show the impact of these optimization techniques on interconnect performance in each technology generation from the 0.35µm to 0.07µm projected in the National Technology Roadmap for Semiconductors.

As the IC devices is scaled into nanometer dimen- sions and operates in giga-hertz frequencies, interconnect design and optimization have become critical in determining the system performance and reliability.

Buffer insertion has successfully been applied to reduce delay in global interconnect paths; however, existing techniques only optimize delay and timing slack. With the increasing ratio of coupling to total capacitance and the use of aggressive dynamic logic circuit families, noise is becoming a major design bottleneck. We present comprehensive buffer insertion techniques for noise and delay optimization. Our experiments on a microprocessor design show that our approach fixes all noise violations that were identified by a detailed, simulation-based noise analysis tool. Further, we show that the performance penalty induced by optimizing both delay and noise as opposed to only delay is 2%. 1.

This paper presents an efficient approach to perform global interconnect sizing and spacing (GISS) for multiple nets to minimize interconnect delays with consideration of coupling capacitance, in addition to area and fringing capacitances. We introduce the formulation of symmetric and asymmetric wire sizing and spacing. We prove two important results on the symmetric and asymmetric effective-fringing properties which leadtoavery effective bound computation algorithm to compute the upper and lower bounds of the optimal wire sizing and spacing solution for all nets under consideration. Our experiments show that in most cases the upper and lower bounds meet quickly after a few iterations and we actually obtain the optimal solution. To our knowledge, this is the first in-depth study of global wire sizing and spacing for multiple nets with consideration of coupling capacitance. Experimental results show that our GISS solutions lead to substantial delay reduction than existing single net wire-sizing solutions without consideration of coupling capacitance.

As technology scales, interconnect-centric design flows become imperative for achieving timing closure. Preplanning buffers and wires in the layout is critical for such flows. Both buffers and wires must be considered simultaneously, since wire routes determine buffer requirements and buffer locations constrain the wire routes. In contrast to recently proposed buffer-block planning approaches, our novel design methodology distributes a set of buffer sites throughout the design. This allows one to use a tile graph to abstract the buffer planning problem and simultaneously address wire planning. We present a four-stage heuristic called resource allocation for buffer and interconnect distribution for resource allocation that includes a new, efficient technique for buffer insertion using a length-based constraint. Extensive experiments validate the effectiveness of this approach.

Deep submicron effects, along with increasing interconnect densities, have increased the complexity of the routing problem. Whereas previously we could focus on minimizing wirelength, we must now consider a variety of objectives during routing. For example, an increased amount of timing restrictions means that we must minimize interconnect delay. But, interconnect delay is no longer simply related to wirelength. Coupling capacitance has become a dominant component of delay due to the shrinking of device sizes. Regardless, the most important objective is producing a routable circuit. Unfortunately, this often conflicts with minimizing interconnect delay as minimum delay routes create congested areas, for which an exact routing cannot be realized without violating design rules. In this work, we use the concept of pattern routing to develop algorithms that guide the router to a solution that minimizes interconnect delay---by considering both coupling and wirelength---without damaging the routability of the circuit. The paper is divided into two parts. The first part demonstrates that pattern routing can be used without affecting the routability of the circuit. We propose two schemes to choose a set of nets to pattern route. Using these schemes, we show that the routability is not hindered. The second part builds on the previous part by presenting a framework for coupling reduction using pattern routing. We develop theory and algorithms relating pattern routing and coupling. Additionally, we give suggestions on how to extend our theory and use our algorithms for both global and detailed routing.

Abstract—Closed-form solutions for the 50 % delay, rise time, overshoots, and settling time of signals in an tree are presented. These solutions have the same accuracy characteristics of the Elmore delay for trees and preserves the simplicity and recursive characteristics of the Elmore delay. Specifically, the complexity of calculating the time domain responses at all the nodes of an tree is linearly proportional to the number of branches in the tree and the solutions are always stable. The closed-form expressions introduced here consider all damping conditions of an circuit including the underdamped response, which is not considered by the Elmore delay due to the nonmonotone nature of the response. The continuous analytical nature of the solutions makes these expressions suitable for design methodologies and optimization techniques. Also, the solutions have significantly improved accuracy as compared to the Elmore delay for an overdamped response. The solutions introduced here for trees can be practically used for the same purposes that the Elmore delay is used for trees.

In this paper we present a repeater block planning algorithm forinterconnect-centric floorplanning. We introduce the concept of